Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Fort Lauderdale?
Gate parts and welding work in Fort Lauderdale typically runs $150 to $550 for most residential repairs, with full gate fabrication and installation ranging from $800 to $4,500 depending on size, material, and the extent of welding required. A broken gate hinge reweld usually lands between $180 and $320, while a custom steel gate build with fresh powder coating starts around $1,800. Those are real numbers for the Fort Lauderdale market in 2026, not national averages: the salt air, intense sun, and frequent afternoon storms here shape what breaks and what it costs to fix.
Key Takeaways
- Small weld repairs (hinge rewelds, bracket fixes, picket reattachment) run $150 – $350 in Fort Lauderdale.
- Gate operator parts (actuators, control boards, receivers, safety sensors) range $180 – $950 parts and labor depending on brand.
- Full custom gate fabrication with welding and installation starts near $1,800 and can exceed $4,500 for heavy steel or aluminum drive gates.
- Salt corrosion is the single biggest cost driver in Fort Lauderdale: gates within a mile of the Intracoastal need more frequent hinge and weld repair than inland neighborhoods.
- Portcullis Gate Repair Fort Lauderdale gives you a written price before any work begins, coverd by the 365-Day Done Right Promise.
Gate Parts & Welding Cost Breakdown (2026)
Here are the line-item price ranges we quote across Fort Lauderdale, from Coral Ridge to Victoria Park to Harbor Beach. These include parts and labor, with the welding done by a uniformed technician who arrives in a marked truck with a written price already in your hands.
| Repair or Part | Typical Cost Range (Parts & Labor) | What It Involves |
|---|---|---|
| Hinge reweld and reinforcement | $180 – $350 | Grinding out the old weld, rewelding, adding a reinforcement plate where needed |
| Gate frame repair (bent or cracked) | $250 – $600 | Straightening or splicing the frame, then rewelding and touch-up paint |
| Picket or finial reattachment | $120 – $280 | Welding loose pickets back in place, spot rust treatment |
| Bracket or post repair | $150 – $400 | Fixing or replacing the mounting bracket that holds the gate to the post |
| Gate actuator replacement (swing or slide) | $350 – $950 | The motorized arm that pushes the gate open; includes removal, new actuator, mounting, and travel adjustment |
| Control board replacement | $280 – $750 | The circuit board inside the gate operator that processes remote and keypad signals |
| Photo-eye safety sensor replacement | $150 – $300 | The sensor pair that tells the gate to stop if something is in the way |
| Remote or keypad programming and replacement | $75 – $200 | New remote or wireless keypad, synced to your existing operator |
| Chain or belt replacement (slide gates) | $180 – $420 | Replacing a stretched or rusted chain, re-tensioning the drive |
| Aluminum weld repair (repair of a broken weld on aluminum gate) | $200 – $500 | Aluminum takes a different alloy filler rod and slower heat; costs run slightly above steel |
| Custom gate fabrication (basic single walk gate) | $800 – $1,800 | Built to your opening size, welded steel or aluminum, primed and painted |
| Custom drive gate (double swing or slide) | $1,800 – $4,500+ | Heavy-gauge steel or aluminum, welded frame, hinges, latch, and optional operator prep |
Those numbers reflect what we actually bill in Fort Lauderdale in 2026. The biggest swing factor is material: aluminum costs more per linear foot than steel but resists the Fort Lauderdale salt air better, so for coastal neighborhoods like Las Olas Isles and Rio Vista, aluminum often pays for itself in fewer repair calls. Steel is stronger per dollar and fine for inland areas like Plantation or Davie, but it requires a solid primer and finish coat if you’re within a mile of salt water.
What Affects Gate Parts & Welding Pricing in Fort Lauderdale
Five things move the number on your invoice. Knowing them ahead of time makes you a smarter buyer and helps you spot a quote that’s either too cheap to be real or padded with work you don’t need.
- Distance from the ocean. Salt air corrodes mild steel fast. A gate in Harbor Beach or Nurmi Isles will need hinge and weld attention every two to four years, while the same gate in Sunrise or Plantation might run six to eight years between repairs. If a quote seems high, ask what gauge and finish the technician is quoting; on the water, you want 14-gauge or thicker steel with a marine-grade primer, or aluminum from the start.
- Gate material. Welding aluminum requires different filler rod, a different machine setting, and more setup time than mild steel. Aluminum weld repairs usually run 20% to 40% higher than the equivalent steel fix. Wrought iron (actually mild steel in most modern gates) is the most forgiving to weld and cheapest to repair.
- Size and weight of the gate. A 6-foot walk gate and a 16-foot drive gate are different jobs entirely. Drive gates weigh 300 to 900 pounds, which means the technician needs to support the gate properly before cutting any hinge loose. That’s more labor, more safety rigging, and a higher bill. The price gap is real: the same hinge reweld costs around $200 on a walk gate and $300 to $350 on a heavy swing driveway gate.
- Operator brand and age. Control boards and actuators differ in price by brand. LiftMaster and Linear boards are common enough to keep prices moderate. FAAC and Viking parts carry a premium and sometimes require a few extra days of lead time. DoorKing parts sit in the middle. When we send a technician to Fort Lauderdale, they arrive certified on nine major operator brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, so you’re not paying for on-the-job learning.
- Access and cleanup time. If the gate post is buried in hedges, or the driveway is a tight turn off a canal street, the job takes longer. We build that into the written price up front, which means no surprise labor fee at the end. That’s part of the Kingswell Guarantee on every job we do.
How to Save on Gate Parts & Welding in Fort Lauderdale
None of these tips involve cheaping out on the weld itself. A poorly done weld on a 500-pound gate is a safety hazard and a future invoice. Instead, save smart:
- Bundle repairs. If one hinge is cracked, the other hinge usually isn’t far behind, especially in Fort Lauderdale’s salt air. Fixing both hinges in one visit costs less than two separate trips because you’re not paying double for the service call and equipment setup.
- Catch corrosion early. Surface rust on a gate frame or hinge is a $120 cleanup and touch-up job. Let it go until the hinge tears loose and you’re looking at $300 plus a possible gate realignment. If you live in Colee Hammock or Victoria Park, put a rust check on your annual hurricane-prep list.
- Choose the right finish. A marine-grade primer plus a quality topcoat runs $75 to $150 extra on a repair. It’s the cheapest insurance you can buy on a steel gate in a salt air zone. Powder coating a new gate at fabrication costs more upfront but extends the finish life by years.
- Ask about the write-up before work starts. Every Portcullis Gate Repair customer gets a written price before the first tool comes off the truck. That’s not a sales pitch; it’s how we work. If you get three quotes, compare them line by line and ask what finish coating is included. A low quote without a finish coat just means you’ll repaint in 18 months.
- Use the free estimate. Call (754) 354-7351 and tell us what’s going on with your gate. We’ll walk through what we think it costs over the phone and schedule a visit with a real arrival window. Estimates are free, and the price you get in writing is the price you pay.
How the Kingswell Guarantee Protects Your Gate Repair
Portcullis Gate Repair Fort Lauderdale is an independently owned Kingswell company. We’ve operated since 2008 under the same four promises every Kingswell company makes: a written price before any work starts, a real arrival window, a clean job site, and a written guarantee on the repair.
For gate parts and welding, that guarantee matters. A weld can look fine and fail six months later if the underlying metal wasn’t prepared correctly. A new control board can misbehave in humid Fort Lauderdale weather. If the repair fails within 365 days, we come back and fix it at no charge. That’s the 365-Day Done Right Promise, stamped in writing on your invoice. No phone menus, no callback queue, no ghosting. Someone answers when you call, 24 hours a day, 7 days a week.
The Kingswell Way is five plain commitments: say the price before the work; show up in the window we gave; leave the place cleaner than we found it; put the guarantee in writing; come back if it fails. That last one is the one that should matter to any Fort Lauderdale homeowner who’s been burned before.
Gate Parts We Replace Most Often in Fort Lauderdale
This is what actually breaks here, based on the service calls we run across the city every week:
Hinges and Weld Points
Hinges are the single most common weld failure on Fort Lauderdale gates. The constant humidity weakens paint, the salt air finds bare steel, and the hinge becomes the first point of structural failure. A hinge reweld on a 6-foot walk gate at a home in Sailboat Bend runs around $180 to $250. On a double drive gate in Rio Vista, expect $300 to $350 because the gate has to be supported while the technician works.
Gate Actuators
The actuator is the motorized arm that physically pushes or pulls the gate open. Florida’s heat and humidity are hard on actuator internals; we replace actuators on gates that are eight to twelve years old with some regularity. A replacement swing-gate actuator runs $350 to $900 depending on whether it’s a light residential unit or a heavier commercial-grade drive. Brands like LiftMaster and Mighty Mule keep prices on the low end; FAAC and BFT sit higher because of the engineering in the unit. We service all nine major brands, which means the technician who shows up at your Fort Lauderdale home already knows the torque specs and wiring configuration for your specific operator.
Control Boards
The control board is the small circuit board inside the gate operator box, the piece that interprets signals from your remote, keypad, or vehicle sensors. Fort Lauderdale’s lightning-heavy summer storms are not kind to control boards; a nearby strike can fry a board even when the rest of the operator is fine. Replacement runs $280 to $750. If your gate won’t respond to the remote but the manual release works, the control board is the first suspect.
Photo-Eye Sensors
These are the small paired sensors mounted near the bottom of the gate track or swing path. They tell the gate to stop or reverse if a child, pet, or car is in the way. They fail from sun exposure, water intrusion, and misalignment. A replacement pair runs $150 to $300, and it’s a safety item you should not defer.
Chain and Belt Drives
Slide gates run on a chain or belt that pulls the gate along the track. Fort Lauderdale’s salt air is brutal on chains; we see stretched, rusted, and snapped chains on slide gates all over Coral Ridge and Bay Colony. Chain replacement runs $180 to $420 including tensioning and track alignment. A chain that’s run without lubrication for years is a $400 fix waiting to happen.
Steel vs. Aluminum: What Fort Lauderdale Salt Air Does to Your Gate
If you’re within two miles of the Atlantic or the Intracoastal, your gate lives in a corrosive environment. We see it every day: steel gates with rust blooms at every weld, aluminum gates with a fine white powder at the joints, and hardware that has seized from salt buildup.
Steel is cheaper to work with and easier to weld, which makes it the default for most Fort Lauderdale gates. But it requires a proper coating. A steel gate with bare welds or scratched paint near Harbor Beach starts showing rust inside six months. The good news: steel weld repair is straightforward, and a competent technician can grind out rust damage and re-weld a hinge or frame splice in an afternoon.
Aluminum resists salt corrosion naturally, which is why we recommend it for waterfront properties. The trade-off is repair cost: aluminum welding requires specific filler alloy and a lighter touch, so aluminum weld repairs run about 20% to 40% higher than the same repair on steel. For a new gate, aluminum costs more per foot but pays it back in longevity near the water.
Safety Note on Welding and Gate Springs
Welding is not a DIY job, and neither is working on gate hardware under tension. A heavy driveway gate can weigh 900 pounds or more; if a hinge lets go while the gate is unsupported, it can crush a person. Gate springs, when present, are under enough stored tension to cause serious injury if released improperly. We do not recommend attempting weld repairs or spring work on your own gate. Our technicians carry the right support jacks, welding equipment, and personal protective gear, and they do this work every day across Fort Lauderdale.
Is It Cheaper to Repair or Replace a Gate?
Here’s the practical math. If the gate frame is structurally sound and the damage is localized (a broken hinge, a cracked picket, a failing actuator), repair is almost always the better value in the near term. A $250 hinge reweld on a gate that would cost $2,500 to replace is a no-brainer.
The calculus flips when the frame itself has rusted through in multiple places, or when you’re paying for weld repairs every year. A Fort Lauderdale steel gate that’s been on the property since 2005, has rust at every picket base, and needs three separate weld repairs in a single year is a replacement candidate. At that point, a new gate fabricated to your opening, with a proper marine finish, will cost less over five years than continuing to patch the old one.
If you’re on the fence, call (754) 354-7351 and describe what you’re seeing. We’ll give you an honest read on repair versus replace, with dollar figures for both, before you commit to anything.
Same-Day Gate Parts & Welding Service in Fort Lauderdale
A gate that won’t close is a security problem and a liability. That’s why we keep common gate parts stocked on our Fort Lauderdale trucks: hinges, brackets, photo-eyes, remotes, common control boards, and standard actuator models. When a customer in Colee Hammock calls at 8 a.m. about a gate that won’t close, we can often have it fixed and secured by early afternoon. Not every repair can be same-day; a custom-fabricated gate or a rare operator part may take a couple of days. But we answer the phone 24/7, and we’ll tell you honestly whether your repair is a same-day fix or a scheduled visit.
Every service visit includes the written Kingswell Guarantee: written price, real arrival window, clean job site, and written guarantee. If the technician says 9 to 11 a.m., that’s the window. You don’t have to take a day off work and hope. You’ll know who’s coming: a background-checked, uniformed technician in a marked Portcullis vehicle.
FAQs – Gate Parts & Welding Cost in Fort Lauderdale
How much does gate welding cost in Fort Lauderdale?
Most welding repairs in Fort Lauderdale run $150 to $550, depending on the specific repair. A hinge reweld on a residential walk gate costs about $180 to $250. A frame crack repair runs $250 to $400. A double drive gate hinge reweld with reinforcement runs $300 to $350. Call (754) 354-7351 for a written quote specific to your gate; estimates are free.
How much does it cost to replace a gate opener actuator in Fort Lauderdale?
A swing or slide gate actuator replacement runs $350 to $950 parts and labor in Fort Lauderdale. The spread depends on the brand: LiftMaster and Mighty Mule units sit on the lower end, while FAAC and BFT units run higher. The replacement includes removing the old actuator, mounting the new one, wiring it to your existing control board, and adjusting travel limits.
Is it cheaper to repair or replace a gate?
For most Fort Lauderdale gates, repair is significantly cheaper in the near term. A typical weld repair runs $150 to $550, while a replacement gate fabrication and installation starts around $1,800. Replacement makes sense when the frame has multiple rust-through points or you’re paying for annual weld repairs. Call us at (754) 354-7351 and we’ll give you honest numbers for both paths.
How much does a new custom gate cost in Fort Lauderdale?
A new custom walk gate runs $800 to $1,800. A double drive gate, fabricated and welded to fit, runs $1,800 to $4,500 or more depending on size, material, and finish. Aluminum costs more than steel but holds up better near salt water. Every fabrication quote is in writing before you agree to anything.
Can you fix my gate the same day in Fort Lauderdale?
In many cases, yes. We keep common gate parts and welding equipment on our Fort Lauderdale trucks, so a hinge repair or sensor replacement can often be completed same-day. Custom fabrication or rare operator parts may take a couple of days. Call (754) 354-7351 and a live person will tell you what’s realistic for your specific repair.
What does the 365-Day Done Right Promise cover?
Every gate parts or welding repair we perform carries a written 365-day guarantee. If the repair fails inside one year, we return and fix it at no charge. The second visit is free. That guarantee is stamped on the invoice in writing, covering parts and labor. It’s the same across every Kingswell company, and it’s the reason we put the price in writing before we start.
Get a Written Price for Your Gate Repair in Fort Lauderdale
If your gate is sagging, stuck, or refusing to close, don’t guess at the cost. Call (754) 354-7351 and talk to a live person who can give you a straight answer on price, timing, and what needs to be done. We’ll schedule a visit with a real arrival window. The technician who shows up is background-checked, uniformed, and carrying the tools and parts to do the job right. You’ll get the price in writing before any work starts. If it fails within 365 days, we come back and make it right. That’s the Kingswell Way, and it’s how Portcullis Gate Repair Fort Lauderdale has done business since 2008.
For more on what we do, see our Gate Parts & Welding in Fort Lauderdale service page, or head back to the home page to explore all our gate repair services.
Pricing reflects the Fort Lauderdale market as of 2026. Portcullis Gate Repair Fort Lauderdale offers free estimates – call (754) 354-7351.
Written by Dean Prescott, Owner at Portcullis Gate Repair Fort Lauderdale, serving Fort Lauderdale since 2008.
What Our Customers Say
"Electric gate kept doing its own thing, opening at random. The tech found a shorted sensor and a worn board, fixed both, and showed me the old parts. Price was what he quoted on the phone."
- Cassandra Pike"Installed a new gate for us after the old wooden one rotted out. Clean work, showed up on time both days, and the written price didn't change. It swings perfectly."
- Donna Kirkpatrick"Gate wouldn't respond to the remote or the keypad. Turned out to be the control board. They had the part and swapped it the same visit. Quoted it first, no surprises."
- Everett Shaw