FAAC Gate Installation Nationwide

FAAC Gate Installation in Fort Lauderdale: What to Know First

FAAC gate installation in Fort Lauderdale typically runs $1,850 to $4,600 for a complete single swing gate with operator, and most jobs are finished in one to two days once parts are on hand. We are an independent FAAC service provider, not a manufacturer-authorized dealer, which means we answer to you and the written Kingswell Guarantee on every invoice. If you already own a FAAC operator and need it installed, swapped onto a new gate, or rebuilt after a failed DIY attempt, this page tells you what to expect before you spend a dollar. Call (754) 354-7351 and a live person answers, day or night.

Call (754) 354-7351

How FAAC Products Fail – and How We Fix Them

FAAC builds solid equipment, but Fort Lauderdale’s salt air, heat, and daily rain expose weaknesses you won’t see in the owner’s manual. Here are the failure patterns we see most often when we arrive at a new FAAC installation job in Fort Lauderdale:

• FAAC S418 and S450H slave-leaf drift. On double swing gates, the slave leaf starts lagging or closing out of sequence. The cause is usually a worn connecting rod or a slave board that lost its limit sync after a power surge. We re-time both leaves, replace the connecting rod bushing if it’s sloppy, and reset the board’s delay parameters rather than throwing a new operator at the problem.
• FAAC 750 and 844 hydraulic pump seal weep. These older hydraulic operators are common in Fort Lauderdale’s established neighborhoods like Rio Vista and Victoria Park. A thin oil film at the pump body means the shaft seal is drying out from heat cycling. We replace the seal and flush the hydraulic fluid before it takes out the pump. That is a $140 to $220 fix that prevents a $900 pump replacement.
• FAAC C720 and C721 capacitor failure in summer. The C-series slide operators run on capacitor-start motors, and South Florida’s August heat kills capacitors faster than almost anything else. The symptom is a gate that hums but won’t move, or trips the breaker. We stock replacement capacitors rated for continuous outdoor duty and always check the run capacitor’s microfarad reading, not just the start capacitor, because a weak run capacitor shortens motor life.
• FAAC S800H control board corrosion. We open the plastic housing on an S800H and find green crust across the terminal strip more often in Fort Lauderdale than anywhere else. Condensation from the Intracoastal breeze gets in through the wiring knockouts. We replace the corroded terminals if the board is salvageable, apply dielectric grease, and seal the knockout properly so it doesn’t come back in eight months.
• FAAC 391 and 400 gate operator arm bracket stress cracks. These compact swing operators are popular on pedestrian gates and lighter driveway gates. The aluminum bracket that mounts to the gate post develops hairline cracks when the hinge side sags and the operator arm is doing the structural work the hinge used to do. We pull the gate, rebuild the hinge post if needed, and weld or replace the bracket before remounting the operator. Installing a new FAAC arm on a sagging gate just transfers the failure to the new unit.

Our FAAC Gate Installation Process

Every FAAC job follows the same sequence, whether it’s a fresh install on a new driveway gate or a repair that turned into a replacement. Here’s how it works when you call Portcullis Gate Repair Fort Lauderdale:

1. 1
   You call and describe what the gate is doing. We ask enough questions to send the right tech with the right parts the first time. If it’s an emergency, we tell you a real arrival window, not “sometime today.”
2. 2
   We diagnose on site. The technician checks the operator, the hinge geometry, the power supply, and the safety sensors before touching anything. No parts come off until you know what’s wrong and what it will cost.
3. 3
   We give you the written price. Before a single bolt is turned, you get a dollar figure for parts and labor. You approve it, or you don’t. No surprises at the end of the job.
4. 4
   Parts decision. For FAAC work we recommend OEM boards, limit switches, and capacitors because aftermarket electronics fail faster in coastal humidity. On mechanical parts like brackets, bushings, and connecting rods, a quality aftermarket replacement can sometimes match OEM at a better price. We walk you through the trade-off in plain English.
5. 5
   Install, test, and verify. We mount the operator, set the limits, adjust the force so it stops on your hand without bouncing back, and test the photo eyes and safety edges from both directions. We run the gate through at least 20 full cycles before we call it done.
6. 6
   Cleanup, walkthrough, and the written Kingswell Guarantee. We leave the gate area cleaner than we found it, show you what we did, and hand you an invoice with the 365-day guarantee written on it. If the repair fails inside that period, we come back and fix it at no charge.

What FAAC Gate Installation Costs in Fort Lauderdale

Straight dollar ranges keep everyone honest. Here is what FAAC work runs in Fort Lauderdale:

• New FAAC S418 or S450H operator installed on an existing single swing gate: $1,850 to $3,200, including the operator, brackets, wiring to the panel, and full limit and force setup.
• New FAAC C720 slide operator installed on an existing chain-driven slide gate: $2,200 to $3,800 depending on chain length, motor mounting plate work, and whether the existing safety loops need replacement.
• FAAC 391 pedestrian gate operator installed on a new or existing pedestrian gate: $1,400 to $2,400.
• Repair work on an existing FAAC unit (boards, capacitors, limit switches, seals): $180 to $850 depending on the part and the access. Most capacitor and limit switch swaps run $180 to $340 parts and labor.
• Full double swing gate with two FAAC operators, new hinges, and safety edges: $4,600 to $7,800.

What moves the price: gate weight and length, condition of the existing posts, whether the power run needs to be extended, and whether your safety loops or photo eyes are still in good shape. Every quote is written, agreed, and signed before work starts. Call (754) 354-7351 for a free estimate on your specific gate.

Why Fort Lauderdale Homeowners Call Portcullis Gate Repair Fort Lauderdale for FAAC Work

Dean Prescott has been working gates since trade school in Los Angeles, and he’s spent years in Fort Lauderdale dealing with everything from failed loop detectors in Las Olas driveways to full operator replacements on Intracoastal-front properties. He’d rather explain what went wrong on a previous repair than pretend it didn’t, and his crew follows the same Kingswell Way on every job: say the price before the work, show up in the window we gave, leave the place cleaner than we found it, put the guarantee in writing, and come back if it fails. That’s the Kingswell Guarantee, and it’s stamped on every invoice. If your FAAC unit is down and we find it’s beyond repair, we also service LiftMaster, Mighty Mule, Ghost Controls, and DoorKing so you’re never stuck waiting on a brand you can’t get parts for. A written price first, then the work – that’s how we do it.

FAQs